Skip to content

ReadyMadeRC

LADYBIRD V2 FPV & RTF WITH DEVO F4 RADIO

1). Dimensions8.5*8.5cm
2). Height3cm
3). Weight33g
4). Motors (x4)0720RN57A-9M-130NL52
5). ReceiverRX2643H-D
6). Battery3.7V 240mAh
7). Radio range<=100m
8). Flight time6-8min
9). Standard transmitterDEVO F4
10).Optional transmitterDEVO 6/7/8s/10/12s
3). Compatible with DEVO series radioDevo 12S/8S/10/7/7E/6S/2402D.Cute and lifelike appearance similar to Ladybird.

Tx5805 Video Transmitter/Camera Specs:, - PAL/NTSC, Ladybird Specs:,

Walkera Ladybird V2 with built in FPV camera and transmitter. ...

ReadyMadeRC

RMRC 2100MAH 3S 3C LIFE TRANSMITTER PACK (FUTABA/JR) PICKUP ONLY

Capacity2100mAh
Type3S1P / 9.9v / 3Cell
Constant Discharge20C (42A)
Peak Discharge (2 sec burst)40C (84A)
Pack Size100 x 30 x 30mm
Charge PlugJST-XH
Power ConnectorFutaba Male
Watt Hours23.31

Note:, We recommed a charge rating of 1C (2.5A) or less for this pack. Always remove battery from transmitter before charging., Pack Weight:, 5.6 oz (161g) including wires/connector,

THESE BATTERIES ARE NOT AVAILABLE FOR SHIPPING. STORE PICKUP ONLY. ...

ReadyMadeRC

RMRC 2500MAH 3S 3C LIPO TRANSMITTER PACK (FUTABA/JR)

Capacity2500mAh
Constant Discharge3C (7.5A)
Peak Discharge (2 sec burst)8C (20A)
Pack Size100 x 30 x 25mm
Charge PlugJST-XH
Power ConnectorFutaba Male

Note:, We recommed a charge rating of 1C (2.5A) or less for this pack. Always remove battery from transmitter before charging., Type:, 3S1P / 11.1v / 3Cell, Pack Weight:, 5.3 oz (150g) including wires/connector,

Have the confidence and piece of mind that your transmitter ...

ReadyMadeRC

CASTLE CREATIONS PHOENIX EDGE 75 BRUSHLESS ESC, 34V MAX. W/BEC

MIN2S LiPo MAX

Helis:, 500 class, Fixed wing:, .40 - .52, Input voltage:, Max continuous amperage at full throttle:, 75 amps*, BEC voltage (voltage regulator for powering radio and sevos):, User selectable choice from 5 to 8.4 volt output, BEC output amperage:, 5 amp peak**, Width:, 2.0" (50.8mm), Length:, 2.8" (71.9mm), Height:, 0.9" (23.2mm), Weight w/wires:, 4.0 oz (113.4g), Weight w/o wires:, 2.5 oz (70.9g), Programmability:, Fully programmable Castle feature set using Castle Link USB adapter (coupon for free Castle Link USB adapter included in package) and freely downloadable Castle Link Windows software., Connectors:, Battery and motor connectors sold separately, Tools needed for installation:, Soldering iron and solder to attach bullets to motor wires and battery connector to power wires., *RC HOBBY APPLICATION RATING: 75 amps for the duration of a single 5,000 mAh battery pack with the ESC in contact with a 5 mph airflow of 25C (77F) or cooler air. Controller temperature must never exceed 100C (212F). Exceeding current or temperature ratings may damage components and may shorten the life of the ESC. Always verify system current draw at full-throttle. Decrease load or increase airflow to decrease the ESC’s operating temperature.,

With the debut of the Phoenix Edge series of ESCs ...

ReadyMadeRC

DJI NAZA H - HELICOPTER STABILIZATION CONTROLLER

7.4V0.25
5.8V0.375
Vertical± 0.8m, horizontal
(Naza-H BEC shown in picture is not included with unit ...

ReadyMadeRC

GOPRO-HOUSING "SNAP" V2.0 FOR GOPRO HD2 - WHITE

Weight of the housing alone23 grams
DisclaimerI suggest clipping off one side of the

Most important changes:, - Screw-mechanism instead of the snapping mechanism (details see below), All functions together:, , Screw-Mechanism for a complete protection and a stable mounting:, With version 1 there was a snapping mechanism which was also responsible for the name. The mechanism was very easy to use, but has proven to be not as secure as i wanted it to be. There have been crashes reported where the front plate just flew off, which drastically reduces the safety of your GoPro. The search was long for the best mounting option, but finally a screwing solution has proven to be best. By using specially designed knurled screws, the GoPro can be removed just as easy on the field as with the snapping mechanism, and no tools are needed. There is no open side, which means the GoPro is completely safe inside and can't fall out. Also you do not need any rubber or zip-tie to close it., :, The housing comes with everything you need to install one of the widely available replacement lenses (for the skeleton-housing). It does not need to be glued in, but instead is being hold perfectly tight by 3 nylon screws. This way the lens can be used in different front-plates and/or housings., :, By using 3 countersunk screws and some of the multiple mounting holes, the housing can be mounted very flexible on almost anything., :, "Snap" can be easily installed/uninstalled on the Eyefly frames. This way you can quickly change between different cameras if needed., The special thing: The GoPro can be mounted, so that the lens indeed is really in the middle of the frame, not "a bit" tending to one side (which looks stupid on video)., :, The front-plate allows the usage of different front-plates for different use-cases. The front-plate included in the standard housing is made for installing just the GoPro and nothing else. By using the, A short mounting manual::, 1) Put together "dry", without glueing, to make sure you've got everything right (including GoPro!),

"Snap" is a GoPro-housing, which offers a perfect protection of ...

ReadyMadeRC

GOPRO-HOUSING "SNAP" V2.0 FOR GOPRO HD2 - BLACK

Weight of the housing alone23 grams
DisclaimerI suggest clipping off one side of the

Most important changes:, - Screw-mechanism instead of the snapping mechanism (details see below), All functions together:, , Screw-Mechanism for a complete protection and a stable mounting:, With version 1 there was a snapping mechanism which was also responsible for the name. The mechanism was very easy to use, but has proven to be not as secure as i wanted it to be. There have been crashes reported where the front plate just flew off, which drastically reduces the safety of your GoPro. The search was long for the best mounting option, but finally a screwing solution has proven to be best. By using specially designed knurled screws, the GoPro can be removed just as easy on the field as with the snapping mechanism, and no tools are needed. There is no open side, which means the GoPro is completely safe inside and can't fall out. Also you do not need any rubber or zip-tie to close it., :, The housing comes with everything you need to install one of the widely available replacement lenses (for the skeleton-housing). It does not need to be glued in, but instead is being hold perfectly tight by 3 nylon screws. This way the lens can be used in different front-plates and/or housings., :, By using 3 countersunk screws and some of the multiple mounting holes, the housing can be mounted very flexible on almost anything., :, "Snap" can be easily installed/uninstalled on the Eyefly frames. This way you can quickly change between different cameras if needed., The special thing: The GoPro can be mounted, so that the lens indeed is really in the middle of the frame, not "a bit" tending to one side (which looks stupid on video)., :, The front-plate allows the usage of different front-plates for different use-cases. The front-plate included in the standard housing is made for installing just the GoPro and nothing else. By using the, A short mounting manual::, 1) Put together "dry", without glueing, to make sure you've got everything right (including GoPro!),

"Snap" is a GoPro-housing, which offers a perfect protection of ...

ReadyMadeRC

GOPRO - DUAL CAMERA HOUSING GOPRO+CCD HERO1&2 - WHITE

"Snap-In"-Mechanism for a complete protection and a stable mounting:, We are especially proud of this, thats why the housing has been named after it: Due to a front-plate with a "snap"-mechanism, the box is completely sealed. There is no open side, which means the GoPro is completely safe inside and can't fall out. Also you do not need any rubber or zip-tie to close it., :, The housing comes with everything you need to install one of the widely available replacement lenses (for the skeleton-housing). It does not need to be glued in, but instead is being hold perfectly tight by 3 nylon screws. This way the lens can be used in different front-plates and/or housings., :, By using the 3 countersunk screws and the buttefly nuts included in the Quadrixette 30-frames, the housing can be mounted very flexible, :, "Snap" can be easily installed/uninstalled on the Quadrixette 30/40. This way you can quickly change between different cameras if needed., The special thing: The GoPro can be mounted, so that the lens indeed is really in the middle of the frame, not "a bit" tending to one side (which looks stupid on video).,

"Click" is a mounting system for cameras in the FPV-area. ...

ReadyMadeRC

GOPRO-"SNAP" HOUSING FOR GOPRO HERO3 - BLACK

Weight of the housing includingg screws and lens protection30 grams
DisclaimerI suggest clipping off one side of the nut a bit, so there won't be any part of it that would

All functions together:, , Screw-Mechanism for a complete protection and a stable mounting:, With the first hero1&2-version there was a snapping mechanism which was also responsible for the name. The mechanism was very easy to use, but has proven to be not as secure as i wanted it to be. There have been crashes reported where the front plate just flew off, which drastically reduces the safety of your GoPro. The search was long for the best mounting option, but finally a screwing solution has proven to be best. By using specially designed knurled screws, the GoPro can be removed just as easy on the field as with the snapping mechanism, and no tools are needed. There is no open side, which means the GoPro is completely safe inside and can't fall out. Also you do not need any rubber or zip-tie to close it., :, The housing comes with everything you need to install one of the 2 lens-options. It does not need to be glued in, but instead is being hold perfectly tight by 3 polyamide screws., :, By using 3 countersunk screws and some of the multiple mounting holes, the housing can be mounted very flexible on almost anything., :, "Snap" can be easily installed/uninstalled on the Eyefly frames. This way you can quickly change between different cameras if needed., The special thing: The GoPro can be mounted, so that the lens indeed is really in the middle of the frame, not "a bit" tending to one side (which looks stupid on video)., :, The front-plate allows the usage of different front-plates for different use-cases. The front-plate included in the standard housing is made for installing just the GoPro and nothing else. By using the "duo"-adapter, also available in the shop, you can mount a CCD-cam in addition to the GoPro without an issue., A short mounting manual::, 1) Put together "dry", without glueing, to make sure you've got everything right (including GoPro!),

This GoPro-housing offers a perfect protection of your GoPro against ...

ReadyMadeRC

GOPRO-"SNAP" HOUSING FOR GOPRO HERO3 - WHITE

Weight of the housing includingg screws and lens protection30 grams
DisclaimerI suggest clipping off one side of the nut a bit, so there won't be any part of it that would

All functions together:, , Screw-Mechanism for a complete protection and a stable mounting:, With the first hero1&2-version there was a snapping mechanism which was also responsible for the name. The mechanism was very easy to use, but has proven to be not as secure as i wanted it to be. There have been crashes reported where the front plate just flew off, which drastically reduces the safety of your GoPro. The search was long for the best mounting option, but finally a screwing solution has proven to be best. By using specially designed knurled screws, the GoPro can be removed just as easy on the field as with the snapping mechanism, and no tools are needed. There is no open side, which means the GoPro is completely safe inside and can't fall out. Also you do not need any rubber or zip-tie to close it., :, The housing comes with everything you need to install one of the 2 lens-options. It does not need to be glued in, but instead is being hold perfectly tight by 3 polyamide screws., :, By using 3 countersunk screws and some of the multiple mounting holes, the housing can be mounted very flexible on almost anything., :, "Snap" can be easily installed/uninstalled on the Eyefly frames. This way you can quickly change between different cameras if needed., The special thing: The GoPro can be mounted, so that the lens indeed is really in the middle of the frame, not "a bit" tending to one side (which looks stupid on video)., :, The front-plate allows the usage of different front-plates for different use-cases. The front-plate included in the standard housing is made for installing just the GoPro and nothing else. By using the "duo"-adapter, also available in the shop, you can mount a CCD-cam in addition to the GoPro without an issue., A short mounting manual::, 1) Put together "dry", without glueing, to make sure you've got everything right (including GoPro!),

This GoPro-housing offers a perfect protection of your GoPro against ...

ReadyMadeRC

CASTLE CREATIONS PHOENIX EDGE HV 40 BRUSHLESS ESC

MIN3S LiPo | MAX

Input voltage:,

The auxiliary advantage. With the debut of the Phoenix Edge ...

ReadyMadeRC

CASTLE CREATIONS PHOENIX EDGE HV 60 BRUSHLESS ESC

MIN3S LiPo | MAX

Input voltage:,

The auxiliary advantage. With the debut of the Phoenix Edge ...

ReadyMadeRC

CASTLE CREATIONS PHOENIX EDGE HV 80 BRUSHLESS ESC

MIN3S LiPo | MAX

Input voltage:,

The auxiliary advantage. With the debut of the Phoenix Edge ...

ReadyMadeRC

CASTLE CREATIONS PHOENIX EDGE HV 120 BRUSHLESS ESC

MIN3S LiPo | MAX

Input voltage:,

The auxiliary advantage. With the debut of the Phoenix Edge ...

ReadyMadeRC

CASTLE CREATIONS PHOENIX EDGE HV 160 BRUSHLESS ESC

MIN3S LiPo | MAX

Input voltage:,

The auxiliary advantage. With the debut of the Phoenix Edge ...

BevRC DPCAV Hobby-Lobby HobbyKing LowPriceRC ngHobbies NitroTek R2Hobbies RangeVideo RCTimer ReadyMadeRC HobbyWireless RCPlanet HorizonHobby HiModel OFM GetFPV AMainHobbies SDSHobby GoodLuckBuy Flying-Hobby